Question 1

How much is a high-pressure pump for a FORD Mondeo 2.0 TDCi 115 hp?

Accepted Answer

A remanufactured high-pressure pump for the FORD Mondeo 2.0 TDCi 115 hp starts at €396.00. This engine takes a single reference, R9044A030A: the price shown is the one part that fits your vehicle, with no variant to compare.

Question 2

Which high-pressure pump reference fits the 2.0 TDCi 115 hp?

Accepted Answer

The reference is R9044A030A. It is what settles the match on a FORD Mondeo 3 with the 2.0 TDCi 115 hp engine — not the vehicle's trade name, nor its year.

Question 3

Why is only one reference offered for the 2.0 TDCi 115 hp?

Accepted Answer

Because this engine was built with a single high-pressure pump. Other Mondeo engines carry several references depending on the production period; here the choice is unique, which rules out any risk of error.

Question 4

Where is the reference found on a high-pressure pump removed from a Mondeo 3?

Accepted Answer

It is stamped on the nameplate. The plate stays readable even on a pump fouled with diesel. It is the only reading that confirms the match with R9044A030A.

Question 5

What happens to the old pump from a FORD Mondeo 2.0 TDCi 115 hp?

Accepted Answer

Part R9044A030A is sold as an exchange unit: it has already been rebuilt with new components and pressure-tested, and the pump you remove goes back into the reconditioning circuit. Return terms are stated at checkout.

Question 6

How does exchange pump R9044A030A differ from a new part?

Accepted Answer

An exchange high-pressure pump is an original part rebuilt with new components, then pressure-tested on a bench. It carries the same reference, R9044A030A, and fits in place of the part removed — at a cost that bears no comparison with a new pump.

Question 7

Does pump R9044A030A fit every Mondeo 3?

Accepted Answer

No: it matches Mondeo 3 models fitted with the 2.0 TDCi 115 hp engine. A Mondeo 3 running on petrol, or at a different diesel power output, takes another reference.

Question 8

Is the year of my Mondeo enough to choose the high-pressure pump?

Accepted Answer

No. Two Mondeo of the same year can take different pumps depending on their engine. It is the engine-and-power pairing — here 2.0 TDCi 115 hp — that determines the reference, and the code on the nameplate that confirms it.

Question 9

How do I spot a failing high-pressure pump on a Mondeo 2.0 TDCi 115 hp?

Accepted Answer

On this diesel engine, a weakening pump shows up as long cranking, hesitation on pick-up, power loss under load and a drop into limp mode. These signs overlap with other fuel system faults: diagnosis is a job for a qualified technician.

Question 10

Why does my Mondeo 2.0 TDCi 115 hp go into limp mode?

Accepted Answer

On this 2.0 TDCi 115 hp, the ECU limits the engine when rail pressure no longer reaches the value expected for the 115 hp rated output. A high-pressure pump that can no longer hold pressure is one possible cause, alongside a clogged filter or a faulty regulator.

Question 11

What does exhaust smoke mean on a 2.0 TDCi 115 hp?

Accepted Answer

On this 2.0 TDCi 115 hp diesel engine, black smoke means an over-rich burn and white smoke unburnt fuel — both of which irregular rail pressure can produce. Colour guides the diagnosis, it does not replace it.

Question 12

Does long cranking always come from the high-pressure pump?

Accepted Answer

No. Long cranking can come from the pump itself, but equally from the fuel filter, the pressure regulator or the common rail. The symptom alone is not enough to condemn the part.

Question 13

Which common rail pump family does this engine take?

Accepted Answer

The Bosch CP1, CP3 and CP4 families are covered, and it is reference R9044A030A that identifies the one fitted from new on this 2.0 TDCi 115 hp. The family alone is not enough to order: the code on the nameplate settles it.

Question 14

How do I confirm the fault before ordering pump R9044A030A?

Accepted Answer

By a fault code read and a rail pressure check, carried out by a qualified technician, before any order of reference R9044A030A. That check separates a failed pump from a clogged filter or a leaking injector — three faults with similar symptoms but different remedies.

Question 15

Does pump R9044A030A fit straight onto a 2.0 TDCi 115 hp?

Accepted Answer

Yes: reference R9044A030A is the original fitment for a FORD Mondeo 3 with the 2.0 TDCi 115 hp engine. It keeps the drive, the mounting and the connections of the part removed. Fitting is a job for a qualified automotive technician.

Turbo Garrett 753420-5006S

Injector SIEMENS-VDO 5WS40536

High-pressure pump SIEMENS-VDO 5WS40019

High-pressure pump FORD Mondeo 3 2.0 TDCi 115 hp

Available products

High-pressure pump DELPHI R9044A030A

Related categories

Frequently asked questions

About this category

Diagnostics and wear symptoms

Core deposit and exchange procedure

24-Month warranty & fast delivery

Manufacturer warranty compliance